gmc

  Beginning in 1951, the rear bumper became an option on both Chevrolet and GMC pickups. This required a change in the standard left tail light bracket. The tail light assembly was now unprotected without the bumper. GM created a new bracket design that brought the tail light slightly ahead of the rear edge of the stake pocket. In this...

  The Chevrolet and GMC left commercial taillight used during 1947-1953 is an excellent example of GM's conservative thinking towards trucks. The number one purpose for trucks was work! Therefore, if a part had been very successful on a prior body design, it just might be adapted later as a part in some new styling. Savings were in production costs...

A redesigned parklight assembly was started with the introduction of the 1947 GMC advanced body style. It was placed in the front fender 3-1/2 inches below the headlight ring. A 2-5/8 inch diameter bezel held a domed glass lens to its housing by two barrel screws. The unit was not meant to be a combination turn signal and parklight assembly...

Though items were shared between GMC and Chevrolet trucks between 1936 and 1946, General Motors made sure many parts remained very different during the early years the GMC preferred very few things to be similar to Chevrolet.  Their customers needed to see an almost stand-alone truck with the higher price of the GMC. One very obvious difference is the change in...

Jim Carter Truck Parts seat cover kits are produced with an emphasis on originality. The materials are top quality for many years’ service. Seams, ribbing, etc., are based on original seats. We recommend that installation be done by a professional upholstery company. However, if you wish to do it yourself, here are several important steps to follow: 1. Seat springs...

  During the late-1950's GM car and truck manufacturers begin to install optional V-8 engines in their vehicles. To set the vehicles apart from their six cylinders, V-8 emblems were designed to attract outsiders. This GMC front fender V-8 emblem above was used during 1955 through 1957. The GMC letters were on both six and V-8 trucks. The pictured Hydramatic...

  During the mid 1960's, most still considered pickups work vehicles. The manufacturer designed them as haulers and few people owned them as their only family vehicle. However, a slight change was beginning with truck buyers as Americans began to have more disposable income. GM and other truck producers were aware that extras on work vehicles were finding more buyers...

The 1967 Chevrolet and GMC trucks are noted for numerous one year only features. As the year progressed, engineers made several changes they felt were an improvement over this first year design. For reasons unknown, dash knobs were redesigned. The following pictures show the correct 1967standard knobs with 1.23 inch diameter serrated edges. Compare these with the 1968-72 knobs having...

  With increased prosperity in the USA during the 1960's the demand for more extras on cars and trucks was high. Manufacturers followed this trend with additional features, at least on their top of the line models. GMC followed this movement even though their product was mostly for work related duties. While sharing much sheet metal with Chevrolet, they certainly...

  During the early 1960's GM's majority of truck buyers chose the base truck with few dealer installed options. It was ending an era of very limited disposable income among the average US citizen. General Motors saw the trend toward more extras on trucks and began to offer visual extras such as two tone paint, side trim, and upgraded interiors...

Between 1954 and 1959 the dash cluster of GMC trucks were given a circular opening for a dealer installed clock or tachometer. These trucks left the factory with a blank-out plate to fill this opening. With most GMC's this plate always remained in place as an option was rarely added. The enclosed photo shows both plates used during the period...

With the new Fleetside bed design in 1958 the Chevrolets placed a chrome emblem on the bed side with the word "Fleetside". However, GMC referred to this new bed as a "Wideside" to not copy Chevrolet. A Wideside emblem was never created, thus the GMC bedsides are without letters. NOTE: The horizontal long bedside trim is a 1959 option only...

During the mid 1950's, V-8 engines began to gain popularity. Many became an option in full size cars and trucks that normally were provided with a six cylinder. When this occurred, most vehicles were given a body emblem advertising that the larger power plant was under the hood. GMC trucks were no exception. During the 1955-59 body style, two different...

  These are some very rare photos. It is quite unusual to find 1947-1953 Chevrolet and GMC 1/2 ton bare frames together. Here, you can compare the differences in the front cross members. As the GMC six cylinder is a few inches longer than the Chevrolet, engineers designed two different front engine cross members. In building the truck frame for...

  GMC bumper guards during these years were standard equipment and stamped from the same heavy gauge metal as the bumper (a different style and lighter gauge metal were dealer accessories on Chevrolet light trucks). A slight change in design was made at the end of the 1956 year. A more decorative pointed dimple was given the guards during 1957...

Some trivia from Jim Carter Truck Parts: On the Advanced Design Pickups and larger trucks, the battery was under the passenger side of the cab floor. To protect the battery from road debris (gravel, sand and ice) it was important that it be protected from this coming from the right front tire. Designers of the Chevrolet and GMC installed the...

  These chrome hood ornaments were exclusively tooled for GMC trucks and have no similarity to the Chevrolet style. They are made up of three attached die cast pieces to create the finished product. Their slim base secures to the center of the hood divider strip. These were dealer installed GMC accessories. As trucks at that time were mostly for...

  By 1954, the Korean War shortages were history. More trim and chrome plating began to show up in trucks and cars. The Chevrolet and GMC truck divisions both introduced a deluxe model for their pickups during mid-year 1954. Hopes were to appeal to the emerging buyers with more disposable income. The deluxe model of these two trucks shared most...

During the Advance Design years, 1947-55, Chevrolet and GMC each changed their grille designs twice. GMC made the change at the end of the second year and Chevrolet made the change at the end of the seventh year. Possibly to save tooling cost GMC, not Chevrolet, always used the same grille on all truck sizes in any one year. As...

Between 1947-1953 the Chevrolet 1/2, 3/4, and 1 ton grilles were made from the same tooling. However, the paint colors and some with chrome plating made a difference. For the perfectionist, the following data will help you build a correct grille during your restoration. Painted Grilles 1947-1948 The standard grille has inner and outer bars the body color. Horizontally, a...

Used only the first 1 1/2 years into this body style, these GMC grilles stand out for their different shape and very heavy duty construction. Because of it's weight of this assembly, it sets on the frame rails and is given extra support by a pair of 1 1/2 to 2 ton steel rods extended at an angle to the...

The big news for GMC in 1936 was the introduction of their first 1/2 ton pickup. Though GMC shared cabs with Chevrolet trucks, the visual exterior differences were mostly noticeable in front of the hood. The GMC grill was totally redesigned and did not resemble the Chevrolet truck. This unique grill was modified little between 1936 through 1938 but the...

Many of the tech articles on this web site emphasis's the subtle ways that truck parts were made economically by GM. Truck often received Chevrolet car items that were used the year before. Sometimes even other GM brands sent their older items to be placed on assembly line trucks. Of all the ways GM saved money on truck parts, none...

Early GMC trucks changed their hood side emblems about as much as Chevrolet, however there is no similarity in appearance. The following shows the GMC changes over 14 years. 1935-36   Anodized silver aluminum with a semi-flat black background. (In 1936, GMC entered the light truck market and carried the emblem from larger trucks of earlier year) Right and left are the same...

Companies outside the Chevrolet Motor Division have always produced replacement parts for the aftermarket industry. Manufacturers often begin reproducing non-original parts very soon after a new vehicle is introduced. A problem occurs on decorative trim such as hub caps. Here, Chevrolet (and other manufacturers), display their logo to attract positive attention. To reproduce a Chevrolet hub cap, non-GM companies have...

The 1939-1940 Chevrolet and GMC grilles may look the same when they are seen separately, however they are not! By sharing fenders, hood top, headlight stands, etc. , the grilles overall dimensions had to be the same. To keep each marquee individual, GM made the grilles different. When the two are compared side by side, what a difference! 1939-1940 GMC...

  Though at quick glance, the GMC grilles of these two years may seem the same, however, look close. Changes at the top show slight differences. The die cast assembly at the top of the 1937 grille gives the impression that the vertical grille bars extend through the emblem. They don't! It's an illusion and is die cast. The hood...

The placement of rear axle bumpers by GM on 1/2 tons proved to be an important feature. Owners can often load cargo over recommended weights, their shock absorbers may lose their resistance, and there is the existence of uneven road surfaces. All this can make axle bumpers very important. During the hauling of freight, these bumpers occasionally stop metal to...

  Leaf spring width on 1/2 ton pickups remained at 1 3/4 inches until the introduction of the two inch width on the Task Force 1/2 tons in mid 1955. The early narrow springs worked well considering the engine horsepower and weight limitations of the 1/2 tons. The two inch springs became standard equipment on the rear of the 3/4...

  It was during the 1967-72 years that General Motors began offering more style to their pickup truck line. Though most still considered a truck as a work vehicle, a growing segment of pickup buyers were being strongly influenced by trim and accessories that even rivaled many automobiles. For the first time on GM fleetside pickups, decorative trim became available...

  The main cross grill stamping making up the 1967-1972 GMC grilles may at first appear the same but they definitely are not. The more noticeable difference is the large GMC letters stamped in the center of the 1967 grille (one year only). Therefore, these three letters are not placed on the hood front as during 1968-1972. Between 1967-1970, the...

  During the first year of this new body design GMC's top of the line was referred to as the "Super Custom". An unusual piece of chrome die cast trim was added to this model in the lower center of the front fender this one year. (Not on Chevrolet) It is identifiable in the GMC Master Parts Book as: Group#...

The straight axle ½ ton GM pickups (1959 and older) were built tough! They served their purpose as the best in work vehicles for over 30 years. Other than an occasional kingpin replacement, they were almost 'bullet proof'. In today's world, the reasons for owning an older truck, has generally changed. Most have been retired from work responsibilities and have...

Early Shock Absorbers Trucks of the Advanced Design years were often exposed to the rough terrain of local gravel roads as well as the dirt ruts on the farm. Quality, long life shock absorbers were a necessity. Therefore, this series of trucks in 1947-49 continued with a proven design of shocks carried over from the earlier vehicles. The highly successful...

Mechanical components on trucks were usually kept for many years by GM. Unless an improvement was needed, there was no need to change a proven design. An excellent example of this is the rear ½ ton axle bumper. The design was used from 1929 through 1946 on Chevrolet and GMC ½ tons. A rubber bumper is held down on the...

  Suburbans ' people haulers on a 1/2 ton truck chassis. Not designed for truck freight, the successful Suburban was created to move people. They quickly gained popularity among the military, as crew haulers for companies, and for small rural school buses. By the 1960's, GM began to expand their Suburban market to attract families. To many this would be...

  The seats on this 1962 GMC Suburban are pure factory original. Their shape is designed for only the Suburban body. They allow for access to the rear seat. Horizontal white vinyl in the back rest is characteristic of many GM vehicles during this era. It was an extra touch that added a little more flair to the deluxe models.

With the introduction of GM's new truck body design in mid 1947, a delivered package became available on both Chevrolet and GMC. World War II was in the past, employment was high, and many American truck buyers were willing to pay a little extra for more options on their new vehicle purchase.

  When looking closely at the black 1954 Chevrolet speedometer face, a small 1/8 inch diameter round hole will be noticed at the top and bottom. Owners of 1954 trucks will always be acquainted with the top hole. This emits red light to notify the driver that the high beams are on. Most are not even aware of the existence...

On first glance, most people assume that both Chevy and GMC gauge clusters are fully interchangeable and are the same except for perhaps the minor difference with Chevy oil gauges topping out at 30 psi versus GMC gauges maxing out at 60 psi. But that's quite a bit short of what the actual differences were originally! There are actually no...

  One of the numerous differences in the new 1947 Advance Design trucks is the different position of the mounting tabs on the speedometer. Reasons for doing this on both Chevrolet and GMC are as follows: with the introduction of this body style in mid-1947, both 3 and 4 speed transmissions were the floor shift design. However, in 1948 with...

Maybe the rubber was of lesser quality. Maybe the GM truck division was saving money. For some reason Chevrolet and GMC trucks were not designed for rubber brake and clutch pads.

In designing the panel truck, engineers realized that this vehicle must have a bumper for body protection. This bumper however, created a slight problem! It held the person loading freight further away from the vehicle cargo floor. He was required to lean further forward to reach merchandise. To help solve this problem, GM modified the standard bumper to come closer...

The 1934-36 half ton Chevrolet truck body style always placed their 17' spare in the right fender. Even the Chevrolet car normally used the right side when only one side mount was added. In mid 1936, GMC entered the ½ ton market for the first time. This light truck shared most all sheet metal and chassis components with Chevrolet except...

Due to the abuse given trucks when they once considered only for work, many body components today are damaged beyond repair. During the restoration of your 1947-1955, if you would rather not use a running board splash apron from a parts supplier, there is an alternative. Locate a piece of new flat metal the correct gauge and size of your...

The hood receiver plates through all of the Advance Design years (1947-1955) interchange. It is their attached hood release lever that is different due to the grill change in 1954. Note: The accompanying photos show the extra length of the 1954-1955 lever. To add extra stability to this length, a groove was stamped in the lever to prevent bending.

  The differences found on the cab during the beginning of the Advance Design years are subtle, yet on close study soon become quite evident. It probably exists on all vehicles when a body style is first introduced. Lab tests on a vehicle tend to overlook a few problems that later surface when it is in the hands of the...

From 1941 through 1953 the GM pickup bed sides are the same, however, a major design change began in 1954. This new bed side design with very few modifications continued to the end of the true step beds in 1987. The unique feature of only the 1954 through 1955 mid series bed sides is the flowing grooves that fit the...

Did you ever wonder why the 1934-46 GM trucks show major rust on their horizontal flat sheet metal? The mystery is solved! These pictures show without a doubt what a wonderful home Chevy and GMC trucks provide for field mice. After the truck has been abandoned at the edge of a pasture, placed in a salvage yard, or just stored...

It is so unusual to find an unmolested mid 30s truck! When this all original 21,000 mile 1937 GMC appeared at a recent New England truck show, we had to take notice having never seen the correct installation of the small 3/8” bead cab windlace on an early model. Our camera did some recording.

Curved Windshield The large one-piece laminated safety plate glass windshield has an area of approximately 1116 square inches. Electric Windshield Wipers Provide constant wiping action regardless of engine load or accelerator position. Wipers have 13-inch blades and a wiping speed of 110 strokes per minute. Two-speed wipers, including a push-button-operated windshield washer, are standard. Wiper arms and the metal portions...

To make the base fleetside tailgate just a little different from Chevrolet, GMC kept their letters body color and surrounded them in a contrasting color. On Chevrolet just the letters have the different color. 1967-1972 GMC (above) 1967-1972 Chevrolet (above)

During the 1947-1955 years, pickup's front and rear bumpers are different due to the shape of the body. Unfortunately, the front can be fit on the rear during restorations.

  Without the rubber covering over the metal running boards like GM cars, trucks immediately show scratches from the driver's shoes. This is frustrating to the restorer who has placed so much effort in repairing and painting these boards to pristine condition. Fortunately, a solution exists! The original running board safety treads have been reproduced. These treads were a GM...

  During the 1947-1955 Advance Design years three different stock running boards on pickups and panel trucks were produced. Features such as width, number of ribs, thickness of metal, and length of under-braces are the same. When placed together, a difference in length is obvious. The longest unit was used on the 1 ton pickup and panel trucks with 134...

  One of the most unusual and rare options for the 1947-1955 1/2 tons are 'wide running boards'. The adjacent picture is from the 1949 Chevrolet Salesman's Data Book. The photos below are of used original boards recently found at an Oklahoma swap meet. They consist of 'short' running boards as used on all flatbed ¾ and 1 ton trucks...

In upgrading the Advance Design 1947-1953 cab for 1954, GM engineers created a totally different dash assembly. It required that the radio be much smaller. With better electronic technology and no push buttons, the new 6 volt radio could be placed into the smaller space. They even placed a cardboard sheet above the '54 radio to protect it from settling...

All 1954-1955 Chevrolet/GMC trucks came from the factory with a blank-out plate to cover where the radio would be installed. As this accessory was dealer installed the plate could be removed (probably thrown away) and the new radio added.   This blank-out plate and its two special clips has become very rare in recent years. They are not being reproduced...

  As more restorers become interested in the 1954-1955 Chevrolet truck, the demand for the correct factory accessories has increased demand. Trucks during these early years were used mostly for work and many owners ordered no accessories. Even the heater was often added later. Though locating a restored or restorable factory radio is a difficult task, there is another source...

The common practice of replacing the original differential with a newer high speed assembly usually brings up another question: How do I connect the late model brake cable to the original brake system?

One of the most unusual features of the 1967-1972 series of trucks is the unique placement of the 1969-1972 Chevrolet Blazer and GMC Jimmy radio speaker. Unlike the pickup, Suburban, and large trucks; the radio speaker is not under the top of the dash. In fact, the dash does not even have grille slots to allow sound to come from...

Stainless steel bedstrips are always a nice extra when you give your bedwood a clear finish. Not only do the strips look good but they retain this attractive appearance despite long term bad weather conditions.

Push buttons were discontinued at the end of 1953 and did not reappear until 1967 Prior to 1959 radios used mechanical vibrator tubes. They would operate with either positive or negative ground. A low buzzing sound could always be heard from the tube area before the radio warmed up, once the sound began, the speaker made the buzzing difficult to...

Though Chevrolet and GMC were usually close in their construction during the 1940's, they were far apart in a few areas. GMC in particular advertised some of their major differences as being steps above the competition.

  For the Perfectionist During the first half of the Advance Design years (1947-1955), GM offered a special panel truck as an option. This deluxe model was designed for a company wanting to give a more upscale appearance to their retail customers. During the era of one car families, the lady of the house looked more toward home deliveries for...

Prior to 1941 in GM pickups, the bed wood of choice was oak. The change to yellow pine occurred at this time and it was used until the end of the wood bed floors in 1987. This southern yellow pine is a hard wood and should not be confused with softer white pine.

There are few GM accessories that are more unusual and rare than this item that was seen at a recent truck show. It was offered by GMC dealers in 1958 and 1959.

Since the introduction of GMC's first 1/2 ton pickup in 1936, there has always been a sharing of most sheet metal parts with Chevrolet trucks. This was done mostly for economic reasons. However, when possible, each of the two brands tried to make inexpensive changes to be different than the other. Some specific examples of this occurred during the Advance...

When observing un-restored GM trucks of the 1947-1955 era, one will notice the majority of these vehicles were originally dark green. An explanation is simple. Green was their standard color! If you did not specify one of the other approximately eleven non-extra cost colors, your truck would be delivered green. The standard color of trucks had been thought of as...

In evaluating the available paint colors on 1946 and older GM commercial vehicles, one should keep in mind the general attitude toward pickups and large trucks during that era. Unlike today, customers bought and owned trucks for work! After five o'clock and on weekends most trucks were parked and the family sedan became the driver. This relates not only to...

Serious early truck restorers often ask 'What is the interior color of the original cab sheet metal parts, versus the exterior color?' The answer for the 1934-46 trucks is simple. The removable panels from the cab interior were always the inside color. If a component was welded in as part of the cab structure, it was sprayed the exterior color...

When observing un-restored GM trucks of the 1930-55 era, one will notice the majority of these vehicles were originally dark green. An explanation is simple. Green was their standard color! If you did not specify one of the other approximately eleven non-extra cost colors, your truck would be delivered green. The standard color of truck had been thought of as...

  If you ever wondered about the color of the primer used by GM before the initial paint, these photos give the answer. This 1957 Chevy 1/2 ton had been polished through the paint in most areas. Of course, our question is: Why didn't they stop polishing when the primer first appeared.

Its the annual convention of the American Truck Historical Society. This year, 2010, it is in Pleasanton, California. Over 700 trucks of all sizes and makes gather at the Alameda County Fairgrounds. In a far grassy corner is a sub group of local early GMC owners. Most seem to be acquainted and use this show as a reason to renew old friendships. There are few "trailer queen" trucks in this group, just dependable daily drivers. Most owners know how to repair the occasional problems that are a part of driving a 50 year old truck.

Regular readers of this section know we tend to give credit to trucks that are the more unusual. This month is no exception.

Charlie has owned this truck for over 30 years, since he was 12 years old. He bought it with paper route money. His parents said "What are you gonna do with that truck" he said "gonna drive it". And he did just that after scraping out the oil pan and replacing the fuel tank.

This 1951 GMC advance design half ton is owned by Tom Pryor of Kansas City, Missouri. Found four years ago in Clinton Missouri it was originally an Iowa farm truck. The previous owners had started a very poor attempt at restoration, sanding the old paint with little body repair then applying primer, the truck then sat in the outside elements were surface rust took over on every panel of the truck. The wood bed was rotten, electrical non-existent and field mice had taken over the interior.

It's 1937 and the Great Depression has affected all households. Sales of new cars and trucks have dropped and most manufacturers have permanently shut their doors. The struggling survivors must add ways to stay above the level of bankruptcy.

This 1953 GMC 1/2 ton is certainly one of the more special trucks we see at today's shows. It not only is of interest to people now but would have been a definite attention getter in the 1950's. Jerry Willis of Independence, MO bought this farm truck un-restored in 1995 and is the third owner. He found it in South Missouri so it had not experienced winter road salt. It was a great candidate for restoration.

This old girl is on her 3rd SB305 engine, hauled a ton of sand last week on the leaf springs. It has found a second life hauling the boy scout trailer around. She is equipped with leaf springs, power steering, power brakes, tilt steering wheel, Eldebrock 550 cfm electric choke carburetor, five bolt wheels, and a factory tachometer.

Not only is this 1937 GMC T-14 very unusual but it is one of the only remaining examples of a pure original in existence. It is a part of history and will remain un-restored.

First I would like to thank all of you for great service and quality parts.

You can’t get more unusual than 1 of 1. This is how Ralph Wescott of Largo, FL describes his 1957 GMC Palomino. General Motors built only one! It was produced to draw attention to their truck display at the New York Autorama show in 1957.

This 1951 GMC is a family original. My father bought it new from the local GMC dealer in Fort Benton, Montana and has stayed with us ever since. For years this pickup was used to drive from town, to our farm and back daily.

Maych is a 1972 GMC Sierra Grande 1/2 ton pickup. He is named for my father, Martin Hamilton Patterson. I was 2 years old when my father died in an automobile accident, so I never really knew him. But for as long as I can remember, when friends or relatives spoke of my father they would always call him Maych.

I bought my 1936 GMC T-14 from the second owner in Arizona in 2003. It was restored in 1989 by the original owner who bought it in June of 1936 and the truck has been in Arizona since new until I bought and had it shipped to Florida.

My name is Roger Uttecht. My truck is a 1950 GMC 3/4 ton Pick-up. I did a frame up restoration on my truck over a 2 year period. I used quite a few parts from Jim Carters antique truck parts. The Website provided me with quite a bit of information about what my truck was originally equipped as well as paint colors on the engine and so forth. The truck was originally green, but I painted it to look like a 1952 Chevy Dime Bank that Harley Davidson Motor company put out in 2000.

I note the absence of GMC participation on the featured trucks so I though that I’d send in some photos of my current project: a 1953 GMC 400 series with livestock body and twin double telescoping hoist.

This 1950 GMC longbed 1/2 ton was restored by Dusty Destler, 17, and his father, Dave. Dusty's first vehicle, he bought it when 14, and he and Dave restored it this last two years. Dusty drove it to high school his senior year, and now is off to college. It's his daily driver.

Here are my pics of my 63 GMC Custom Longbed 1002. 305 V6 original with 85000 miles. 4 sp on floor. Truck is painted 1984 VW MARS RED. Original wood bed in good shape

Well this truck has a really long story but I'll try to make it short and sweet. It all started with a trip to my wife’s cousin's farm in Kentucky . We were looking at some of his horses when I saw this old truck next to his barn. I thought to myself, "I sure would love to have that old truck". At the time, I didn't know what would be involved in restoring it.

Hello Jim: My name is Paul McGarr and I bought my "1951 GMC" in 1994. I always wanted one because my dad had a 50 Chevy 5 window when I was a youngster. Originally I wanted to buy a Chevy 5 window but could not find one in half decent shape.

This is my 1946 GMC 1/2 ton pickup. It is designated Model EC-101. I purchased this truck two years ago from the man who restored the truck with the exception of the bed. He had built a wooden bed from pressure-treated pine. Fortunately, he had the original metal bed, which has its original all-metal floor; and it was in surprisingly good condition. I had a body shop sand blast the bed and my local vo-tech school did the paint work. I was given several old Jim Carter Truck Parts catalogs with the truck and found out quickly that Jim Carter is an amazing resource for owners of these trucks. I purchased the rear fenders from Jim Carter and they are clearly the best fiberglass parts I have ever seen.

I bought my '1951 GMC in '1991 and like many people, eventually I found my way to Jim Carter's shop door...or more correctly his catalog and mail order business. At that time, his catalog was just being updated which is still the case! It's constantly being updated. I wish that I had all my old Jim Carter catalogs to go back and look at them because of what is now available versus what was not available from the catalog then. Trust me, the catalog is a LOT thicker now. He used to go from '1934-'1959 in one catalog! Actually I think his first catalog was from '1934-'1972.

My truck is a 1966 GMC three quarter ton pickup with a short Fleetside bed. This truck came to me with the original factory build sheet showing a build date of 6-6-66, and factory equipped with the optional 351 cubic inch V-6, turbo 400 transmission, power steering, power brakes, 4.10 locking rear end, heavy duty springs, and custom cab. It was originally a two-tone truck, green and white, but I had it repainted a 1973 Cadillac color, Sage Metallic. It has just over 50,000 actual miles on it. I've owned it for about 5 years. I bought it from a neighbor who had bought it at the estate sale of the original owners about a year before. It was in great shape - no rust and no dents.

This section of our website gives honor to those Chevrolet and GMC trucks which earn their place by performing various duties. It is not limited only to larger trucks. Both large and small trucks, through the years, have provided continued service for their owners. They have towed, hauled, advertised, delivered, used as the family car, and even been a home away from home.